Dean H

High priority. Read my post on Transmission service. https://www.dodgejourneyforum.com/topic/18151-automatic-transmission-fyi-please-read/

Read this - https://www.dodgejourneyforum.com/topic/18760-journey-maintenance-and-other-fun-facts/

Go here! https://www.dodgejourneyforum.com/topic/18760-journey-maintenance-and-other-fun-facts/

Go here! https://www.dodgejourneyforum.com/topic/18760-journey-maintenance-and-other-fun-facts/

Go here! https://www.dodgejourneyforum.com/topic/18760-journey-maintenance-and-other-fun-facts/

Fluids and basic checks Know what specific type of fluids your year Journey uses. It matters. The reservoir tanks and dip-stick are marked for correct fluid levels. They have yellow caps on them. See pictures at end of this post. 1) coolant level. 2) power steering fluid 3) engine oil 4) brake fluid 5) windshield washer fluid 6) Transmission fluid - if your transmission has the dipstick tube. You will need to buy the dipstick. Read my post and thread here on the Forum. https://www.dodgejourneyforum.com/topic/18151-automatic-transmission-fyi-please-read/ Tire pressure. Consult label on driver's side door jamb. Heater hoses. The Journey has a lot of heater hoses. You should definitely check for leaks. If you have the rear seat AC-Heat controls. There is 2 heater hoses that run from the engine bay. Underneath the passenger floor boards through metal lines to the rear heater core. Then connect to that heater core with rubber hoses. Cabin air filter. Located behind the glove box. EVIC screen located in the center of the instrument cluster. Use the keypad on the left side of the steering wheel. Arrow buttons and the back button. Explore what things you can display on the screen. V6 3.6L engine info. The engine oil filter is located on the top of the engine. Beneath the twist off cap on the engine cover. The oil filter housing and the cap you remove to change it are plastic. If over tightened, the housing will crack and cause an expensive oil leak. Wherever you go for oil changes. You better talk to them so they know all about it. The Journey has a lot of things going on under the hood. That you should monitor and know about. The more often you check your fluids and look around the engine bay. You can catch problems and fix them at your convenience. Before you get stranded somewhere. Dean.

Owners manual 2016.

Go with a cigarette lighter-power port adapter to USB.

Welcome! First thing, you should do is a correct transmission filter and fluid change. Do not wait. The transmission correct service is often neglected. Dodge recommends 120k miles. Your on borrowed time at that mileage. Here is a post, I put together on everything regarding that. https://www.dodgejourneyforum.com/topic/18151-automatic-transmission-fyi-please-read/

Go to Rockautocom. For research it is excellent. Look up your DJ and read through brake pads. Different variables for rotor size and vehicle production date.

Does your steering wheel have the top 2 keypad buttons as seen in the picture below? The VR button, phone button?

Happy to! Do this. For you, get a standard 2 gauge ground cable. Run it from the battery ground stud on the driver's side strut tower to the engine block. The DJ has a weak electrical ground system. Here is my post that explains it entirely. https://www.dodgejourneyforum.com/topic/18374-electrical-system-fyi-ground-system/ Here is my post regarding necessary battery maintenance and upgrades https://www.dodgejourneyforum.com/topic/18210-electrical-system-fyi-battery/ Dean

P0171-FUEL SYSTEM 1/1 LEAN Possible Causes RESTRICTED FUEL SUPPLY LINE FUEL PUMP INLET STRAINER PLUGGED FUEL PUMP MODULE 02 SIGNAL CIRCUIT 02 RETURN CIRCUIT 02 SENSOR MAP SENSOR ECT SENSOR ENGINE MECHANICAL FUEL FILTER/PRESSURE REGULATOR POWERTRAIN CONTROL MODULE (PCM)

You have an engine vacuum leak. The no power brake booster and these codes are vacuum leak related. Trace vacuum lines from the map sensor to the brake booster and the engine source. P2173- HIGH AIRFLOW/VACUUM LEAK DETECTED (SLOW ACCUMULATION) Possible Causes VACUUM LEAK RESTRICTION IN THE EXHAUST SYSTEM INTERNAL ENGINE MECHANICAL COMPONENTS RESISTANCE IN THE 5-VOLT SUPPLY CIRCUIT RESISTANCE IN THE MAP SIGNAL CIRCUIT RESISTANCE IN MAP SENSOR GROUND CIRCUIT MAP SENSOR POWERTRAIN CONTROL MODULE (PCM)

You need to have a bi-directional scan tool. That can communicate with all the modules and test individual components. Perform relearn procedures. I have this one- LAUNCH X431 CRP919EBT Elite... https://www.amazon.com/dp/B0C68BKGN3?ref=ppx_pop_mob_ap_share Please scan for codes and tell me exactly. What they all are right now.

When you replace cam position sensors and the throttle body. There is a scan tool relearn function, that has to be done. Start here.

Life issues. Say no more, I know. So what all have you replaced so far?

If you never did this repair. The BCM is a gateway for all the bus lines. Your in deep. The only person I know of is Ivan in Pennsylvania. https://www.pinehollowdiagnostics.com/

Tell us everything that has been replaced on your DJ. If you replaced any modules BCM, PCM. They have to have the vehicle vin written to it .

Remote Start Operating Conditions. In order to operate remote start, the following conditions must be met- Key fob sequence must be operated within a 100 meter range of the vehicle. The vehicle must be in Park Fobik is not in the vehicle The hazard switch off Vehicle Theft Alarm or Panic is not alarming Doors and hood must be closed. The battery voltage is normal (11 to 15 volts). --Remote Start Shut Down/Deactivate Conditions--- Engine will NOT start or will shut down/deactivate during any of the following conditions below. Doors or hood are opened before remote unlock Hazard Switch depressed Panic or theft alam active Brake applied. If the vehicle is remote started and the customer then unlocks and enters the vehicle, the brake application will not stall the vehicle If the vehicle is remote started and no entry is detected, brake application will shut down the engine Low fuel levels, Fuel indicator active A prior remote start cranked the engine, but failed to start the engine. Battery voltage NOT in the normal range. High (run away) or Low Idle (stall) RPM. MIL Active. High Engine Coolant Temperature. Low Engine Oil Pressure.

P0128 Thermostat rationality. Theory of Operation- The Thermostat is considered malfunctioning if the coolant temperature does not reach the highest temperature required to enable other diagnostics, or the coolant temperature does not reach a warmed up temperature within 20°F of the Thermostat regulating temperature. The Powertrain Control Module (PCM) creates a model of the engine coolant temperature warm up cycle, based on the engine coolant temperature at start up, ambient temperature, vehicle speed and engine speed. The modeled engine coolant temperature is compared to the Engine Coolant Temperature Sensor reading. If the engine actual temperature reaches the calibrated temperature threshold before the model, the diagnostic passes and completes. If the model reaches the calibrated temperature threshold before the engine actual temperature, a pass/fail determination is made based on the difference between the model and actual values. The diagnostic is considered passing if the difference between the engine actual temperature and model is acceptable when the model is greater than the engine but represents the slowest possible warm-up for a "good" thermostat. When Monitored and Set Conditions When Monitored: This diagnostic runs when the following conditions are met With the engine running. Start up coolant temperature less than 65 deg * C (149 deg * F) Ambient temperature between - B deg * C (17.6 deg * F) and 50 deg * C (122 deg * F) Average vehicle speed greater than (10 coolant temperature reaches 85 deg * C Engine speed does not go above 5400 rpm for more than 32 seconds The pass/fail determination point is reached when the coolant temp model reaches 88 deg * C 190 4°F) Set Conditions: The predicted coolant temperature reaches the target threshold before the actual coolant temperature and the PCM detects that the actual engine coolant temperature is too far below the what is acceptable for a good thermostat Default Actions: MIL. light will illuminate Possible Causes --- LOW COOLANT LEVEL --- COOLING SYSTEM ISSUES --- THERMOSTAT OPERATION

What code scanner do you have? You need a bi-directional scanner. That is able to communicate with all the systems on the DJ.

A cars fluids is something you should check regularly. The more often you do. The more problems you will prevent or catch before it gets expensive to fix. The 3.6 is a highly complex engine internally. With it's wide engine RPM band. Your going to use oil. The harder you drive it even more so. With the 3.6 you should be checking the engine fluids once a week. It has a maze of heater hoses to watch as well. The 3.6 liter (219.7 CID) flexible fuel V-6 engine features Variable Valve Timing (VVT), Dual Overhead Camshafts (DOHC) and a high-pressure die-cast aluminum cylinder block with steel liners in a 60° configuration. The 3.6 liter engine has a chain driven variable discharge oil pump with a two-stage pressure regulator for improved fuel economy. The exhaust manifolds are integrated into the cylinder heads for reduced weight. This a view of the complex timing chain on the 3.6. This a cylinder head with the valve cover removed. The 3.6 has 2 cylinder heads. Picture the engine spinning up to 5-6,000 RPM's. You got damn lucky in my opinion.

2016 DJ I marked the power seat 25 A CB and the heated seat fuse.

Laura, Check your forum inbox. I sent you 2 emails.